Delicious - Home Improvement

Suspended ceilings, using a metal lattice or grid and acoustical ceiling tiles are one of the easiest ceilings to install. Yet, home handymen seem to run into numerous problems that result in a poorly crafted overa

According to USFDA, a combination product is one composed of any combination of a drug and device; biological product and device; drug and biological product

ll project.

Following are a few tips from the pros that will result in a ceiling that looks as if a professional installed it.

The placement of the L channel is the most critical structural element of th

; or drug, device, and biological product and fixed dose combination would include two or more combinations of drug.

Examples of combination products may in

e ceiling. All other dimensions and channel placements work from the position of the L channel. If your ceiling height will allow, install the bottom of the L channels 6” below the lowest point of the ceiling. If

lude drug-coated devices, drugs packaged with delivery devices in medical kits, and drugs and devices packaged separately but intended to be used together.

the ceiling height is critical, you can raise the L channel to 3” from the lowest point of the ceiling. If you place the L channel any higher than 3”, you will not be able to maneuver the ceiling tiles into positi

here is enormous increase in the number of combination products entering the market in the recent years. Combination products have proven advantages but fixe

n once the grid is complete.

Do not set the position of the L channel with a tape measure. Measuring from the floor up or from a ceiling joist down is a sure method to install a ceiling that is not level. Use a l

d dose combinations are still in the process of convincing regulatory authority on their advantages over the single ingredient formulations.

Combination pro

aser level to set the positioning of the L channels. Install all of the L channels, securely to the walls before you do anything else.

The ceiling tiles should be balanced. By that, I mean that the size

ucts have become life saving products for the pharmaceutical companies who doesn’t have many innovative molecules in their product pipeline and have been inc

of the tile on one side should be the same as the size of the tile on the opposite side and the same scenario applies to the ends.

To make the ceiling tiles equal on the ends and on the sides, you have to determin

easingly used in the product life cycle management. Even the companies having product patents are trying to extend their product life cycle through the combi

e the size of the ceiling tiles that you are planning on using. Ceiling tiles come as 2’ x 2’ and 2’ x 4’. If you are using 2’x 4’ you must determine whether you want the 4’ dimension running the length or width o

nation products and maximize the revenues. But the companies involved in this practice are overlooking that they are burdening the patients both economically

the room. Using the 4’ dimension length wise, will make the room look longer and narrower, using the 4’ dimension width wise will make the room look shorter and wider.

It really doesn’t matter which direction you

and physically. They need to rightly judge the benefits of the combination products and they have to even look at the risks involved when combining the produ

choose, the method of calculation is the same. However, the resultant will be different. For explanation let us assume that we have a room that is 11’ x 10’ and we are going to use 2’ x 4’ tiles and run the 4’ di

ts. Some of the combination products were well accepted by physicians while others suffered. Companies involved in development of combination products are fi

mension of the tile against the 11’ dimension of the room. You will require 3 tiles, which was determined by dividing the 11’ room dimension by the 4’ tile dimension. However, in this example you will see that you

ding difficulty in defining their combination products and facing various challenges from selecting a combination to marketing it.

Following aspects would a

really need two full tiles and 1 tile that is 0.75 of the length of a full tile, in this case 3’. You can of course start putting in the grid by measuring 4’ from the wall and having two 4’ tiles and one 3’ tile.

dd to the challenges in developing combination products:

Which markets to tap where the combination products can do fairly well?
Which combination prod

This however will not give a professionally installed appearance. You want balance - hence you divide the non 4’ tile in half and make two pieces 1.5’ long. The result is a ceiling that has an initial tile of 1.5’

cts are meaningful and rational?
Which therapeutic categories to select?
Which Combinations can address unmet needs of the patients?
Do combin

, followed by two tiles 4’ long, and finished with another 1.5’ tile.

The same scenario should be applied to the width. In this case, in order to maintain a balanced appearance you would require five tiles, as the

tions increase the patient compliance?
What would be the developing cost?
How to tackle the risks encountered during combination product developmen

width of the tile is 2’ and the width of the room is 10’. Had the width of the room been 9’ you still would have needed five tiles in total – four at their full 2’ width and two at 0.5’ or 6” width.

As the main T

t?

As combination products don't fit into the traditional categories of drugs, medical devices, or biological products, the USFDA is in the process of devel

ee members are notched to accept the Tee cross members it will be necessary to cut the end of the main Tee in order to have the cross members positioned at the proper starting distance from the wall. The main Tee m

ping new procedures for reviewing their safety, efficacy and quality.

Professional from academic institutions, pharmaceutical industries, health care indust

mbers are usually installed perpendicular to the longest wall and should be supported every 4’. It is best if the support wire hangs straight down from the joist. If the wires are on angles, they may cause the cei

y and representatives from various regulatory agencies are working out to design the regulatory requirements for manufacture and sale of combination products

ling to shift.

If you are installing pot or recessed lights, for best visual appeal they should be in the center of a ceiling tile. If you are installing 2’ x 4’ florescent light fixtures in a ceiling ti

.

As there is an increasing trend of the combination products companies manufacturing such products should be able to tackle the problems involved in the de

le position, the light fixture should have support wires attached to at least two opposite corners. A suspended ceiling is not designed to support the weight of a florescent fixture without having the fixture suppo

elopment. They need to be wiser in analyzing the market trends and the regulatory requirements.

Companies that provide selfless information through particip

rted independently. By directly supporting the fixture, you will avoid having the ceiling sag.

As with most home improvement and remodel projects, planning and knowledge are the keys to success.

tion in industry events and feedback to regulatory authorities would be able to face the challenges and will be successful in developing combination products

Tags

Links

Delicious - Installing Suspended Ceilings

Related Articles: